DOYMA Installation Accessories

Aquagard concrete sealant

The system consists of
  • AQUAGARD primer (Curaflex® 1710/1711) Primer for AQUAGARD special paint
    The primer penetrates deep into the capillaries and air bubbles in the concrete, and closes these off so that they are permanently waterproof. This means that water cannot permeate around the gasket insert. The primer is applied using a brush or roller.
  • AQUAGARD special paint (Curaflex® 1715/1716) Special paint for sealing off core drillings
    Aquaguard special paint seals off the surface of the core drilling walls and simultaneously protects any possibly cut reinforcing steel against corrosion. The special paint is also applied with a brush or roller.
Delivery sizes:

AQUAGARD preservative (large)

  • AQUAGARD primer
    1 litres for 4.0 m² (Curaflex® 1710)
  • AQUAGARD special paint
    1 litre for 3.5 m² (Curaflex® 1715)

AQUAGARD preservative (small)

  • AQUAGARD primer
    1/3 litre for 1.5 m² (Curaflex® 1711)
  • AQUAGARD special paint
    1/3 litre for 1.0 m² (Curaflex® 1716)
AQUAGARD Primer Special paint
Yield 3.5 – 4 m2/litre
Colour colourless pigeon grey
Drying time (room temp.) 1 hour 5 – 6 hours
Aquagard concrete sealantConcrete needs protection!

Without protection concrete will permit moisture penetration to some depth before it becomes an absolute barrier – that is how moisture circumvents the gasket.

The product

Aquagard comprises a colourless base primer and a concrete-grey special paint top coat having a coverage of 3.5 – 4 m² per litre; both products can be brush or roller applied. The primer requires about 1 hour ventilation time at room temperature and the top coat will be touch dry within two hours at room temperature and fully cured within five to six hours.


Packings (1775)

Packings (1775)Curaflex® packings (for thin or hard membranes) (1775).

Packings consist of 2 no. 3 mm thick EPDM cutouts which are matched to the dimensions and hole diameters of the selected fixed/loose flange structures.

General

In accordance with DIN 18195-9, single-layer, loosely-laid tanking membranes must be edged using permanently compatible packings on both sides. Sealtightness is only guaranteed for fixed and loose flange structures if the thickness and the elasticity of the tanking membranes or also the packings is sufficient that they are pressed against the substrate to form a seal. Before laying ceiling sheets, the information provided by the sheeting manufacture must be observed in addition to the specifications in the standard (laying guidelines)!

A) Application with very thin or hard sealing sheets – Curaflex® 1775

If tanking membranes are made of very thin and/or very hard materials, even pressing onto the substrate is often insufficient. When such tanking membranes are used, the standard proposes the use of packings.

DOYMA packings are made of material-compatible EPD elastomer and have already been provided with the necessary boltholes on the fixed flange, and are therefore ready for installation. These matching packings are not included in delivery as standard.

B) Application with other sealing sheets

In the case of tanking membranes made, for example, of bitumen or bitumen rubber, even pressing onto the substrate is provided in most cases. In such cases, there are no problems with regard to sealtightness. For this reason, packings are not necessary.


Access reset for bituminous coating

Accessory set for bituminous coating consisting of space at rings, O-rings and fleece inserts. These parts match the dimensions and hole sizes for the selected fixed/loose flange structures when fitted together.

Caution!

If steel pipe sleeves are built into building walls with bituminous coating, the contact surfaces must be sand-coated in the works. When ordering, please always state the following in such cases: “For bituminous coating”.

Access reset for bituminous coating
Layers (from bottom to top):

  • sand coating
  • thick-coated membrane
  • fleece material
  • thick-coated membrane

Access reset for bituminous coating

Punching out holes with the hollow punch

Access reset for bituminous coating

Application description

The contact areas / internal areas of fixed and loose flanges in the Curaflex® 5000, C/2/SD/5, F/2/SD/5 products and the Curaflex® 6000, 7000, 8000, C/2/SD/6 and F/2/SD/6 products will be sand-coated. WEROPOX-EP Primer no. 6142 with 6141- H hardener is used as a carrier material for the leading sand. Areas around drill holes or the bolts themselves, in locations where O-rings and U-washers will be applied, may not be sand-coated. Diameter of these surfaces: 40 mm for non-pressing water, 55 mm for pressing water

Sand coating is not necessary for Curaflex® 4005 and 4006 pipe sleeves.

Bitumen bituminous coating are to be applied in several layers according to the manufacturer’s instructions. Once the first layer has been applied the fleece insert, which is 100 mm larger than the fixed flange all round, is pressed into the first layer while still wet. After this, the fleece insert is trowelled in wet in wet so that the minimum dry layer thickness for the load case in question has been achieved.

Once the drying time stipulated by the manufacturer has expired, the bitumen filling compound will be broken out in the areas around threaded drill holes or bolts, for example using a hollow punch, depending on the version of the fixed or loose flange structure (Accessory Curaflex® hollow punch 1777/6 (5) or 1778/6 (5)). If Curaflex® products against pressing water are being used, spacer rings of 4 mm thickness are to be inserted between the flanges around each bolt, and in the case of Curaflex® products against non-pressing water the spacer rings are of 3 mm thickness. This prevents the overall bitumen filling compound being squeezed out when the loose flange is tightened, and also achieves a defined layer thickness of the bitumen filling compound between the fixed and the loose flange.

Furthermore, rubber O-rings are placed around the bolts and the spacer rings to prevent any possible pressure losses in the areas around the bolts.


Installation tools

Curaflex® 1701 (formwork fastener)

Pipe sleeve inner diameter NB [mm] Formwork fastener outer diameter [mm] Overall length [mm]
80 138 20
100 162 20
125 188 20
150 213 20
200 268 25
250 340 25
300 408 22
350 455 21
400 510 32
Curaflex® 1701Facilitates quick and easy mounting of the sleeve in the formwork. Formwork fasteners are plastic caps with a wide nail rim so that it can be nailed to the shuttering. Available for all sleeves up to 400 mm NB.

Technical details
  • holder for simple and rapid fixing of the pipe sleeve into wooden shuttering.
  • provided with wide nail border for fixing to wooden shuttering.
  • available for pipe sleeves of up to NB 400.
  • material: Plastic

Curaflex® 1702 (protection cap)

Pipe sleeve inner diameter NB [mm] Protection cap outer diameter [mm] Overall length [mm]
80 90 29
100 110 30
125 135 30
150 159,5 33
200 214 38
250 264 46
300 314 23
350 364 28
400 420 33
Curaflex® 1702Plastic cap which serves to close off the sleeve during the main works. Available up to 400 mm NB.

Technical details
  • pipe stoppers fore closing off the pipe sleeve during the shell construction phase to prevent penetration of dirt and foreign objects
  • provided with wide border for secure fixing to pipe sleeve
  • available for pipe sleeves of up to NB 400.
  • material: plastic

Bonding and other accessories

Sikadur 31 concrete adhesive (1740)

Adhesive for glueing the divided 3000/T special fibre cement pipe sleeve. This adhesive also connects the two special fibre cement pipe sleeves to form an elongated pipe length.
1.2 kg, sufficient for approx. 0.6 m²

2-component epoxy resin coating (1745)

Epoxy resin for coating pipe sleeve internal services, front face and core drilling walls. With high chemical resistance; seals off gastight against natural, town and liquid gas, led-free petrols, diesel etc.
2.0 kg, sufficient for approx. 2.0 m²

Sikadur Adhesive Cleaner (1754)

Activator and cleaner of metallic substrates for better bonding of Sikaflex 11 FC+ sealing compound.
1 litre, sufficient for approx. 8 m²

Sika Primer-3N (1755)

Primer for concrete for improving bonding with Sikaflex 11FC+.
0.25 litres, sufficient for approx. 1.25 m²

Sikaflex 11 FC+ (1756) sealing compound.

Elastic sealing compound with excellent strength values. Movement absorption of approx. 10%. Rapid-hardening, permanently elastic. Excellent weathering and ageing stability. Resistant against aqueous cleansing agents, seawater, lime water, weak acids and alkalis and wastewater.
300 ml cartridge, sufficient for approx. 0.24 m².

Butyl sealing tape (1753)

Elastic sealing compound for sealing off existing bituminous coating

 

Curaflex® hollow punch for bituminous coating

subject to pressing water

  • for two applications (1777/6)
  • for multiple applications (1778/6)

subject to non-pressing water

  • for two applications (1777/5)
  • for multiple applications (1778/5)

Fixing set for Curaflex Nova® gasket inserts

Fixing set for Curaflex Nova® gasket inserts

Consisting of 4 stabilising lugs with screws
Article no. 188060000429