DOYMA Curaline® KD 110

Combination flange sleeve / system cap

Curaline® KD 110

  • sealing system for penetrations
  • for buildings yet to be constructed
  • to install in waterproof concrete (white tank)
  • with screw thread
  • suitable for cables and cable protection pipes
No. of spigots
(system cap)
Inside Ø of
spigot [mm]
cable-Ø
[mm]
1 80 26 – 78
1 100 34 – 98
3 46 16 – 44
7 4 x 25
3 x 32
7 – 23
12 – 30
Ld: 140 mm min.

Option

  • Flanged sleeve and
  • conical gasket insert WA/1 x 110
    • for connecting 110 mm external diameter cable duct
    • manufactured from highly durable EPDM elastomer

Option

  • Flanged sleeve and
  • gasket insert WA/Z x D for use instead of the Curaline® system cap and heat shrinking. A conical gasket insert WA, manufactured from highly durable EPDM elastomer, is available for retrofit sealing cables up to 110 mm external diameter. It is in split form to facilitate sealing of one or several cables already installed and is simply pushed into the sleeve and then secured in position by tightening the split collar using the articulated spanner.
Curaline® KD 110

DOYMA 25 Years Guarantee

Product benefits

  • simple installation (with screw connection) through precisefit and matched combination of system cover and seal packing
  • no reworking required
  • several sleeves with flanges can be assembled together in batteries when a multiplicity of cables is to be ducted.
  • the chamfered corners of the packings provide total control of the concrete compaction in the field of cable ducts.
  • high variability thanks to large selection of system caps and additional partition valves
  • by blind cap already in the installation gas- and watertight, even against pressing water

Leak Test: Fraunhofer

Technical details
  • gas-tight
  • screw thread for connecting system caps to sleeve flange
  • suitable for cables 7 – 98 mm diameter
  • cables are sealed to system cap spigots using heat shrink sleeves as standard
  • compatible with existing duct systems
  • materials are ecologically friendly and highly resistant against chemicals

 

The combination package consist of:

  • Flanged sleeve
    – supplied complete with protection plug and peel-off film
    – installed individually or in batteries
    – available for any wall thickness – fits flush within the shuttering
  • System caps
    – quick and simple attachment using screw fastening
    – have 1, 3 or 7 spigots
    – each with its own heat shrink sleeve

 

Product specification

Ordering example:
Single flange sleeve

(1)KD 110 – (2)K / (3)(L)

  1. System identification
  2. Sleeve with a flange on one end
  3. Wall thickness in mm

Ordering example:
Double flange sleeve assembled in a battery of 2 x 3 units

(1)KD 110 – (2)2 x (3)3 – (4)K 2 / (5)L

  1. System identification
  2. 2 sleeves one above the other
  3. 3 sleeves in a row
  4. Sleeve with a flange on both ends
  5. Wall thickness in mm

 

Ordering example:
Angled double flange sleeve in 45° position

(1)KD 110 – (2)S45 – (3)K 2 / (4)L

  1. System identification
  2. Sleeve in 45° position
  3. Sleeve with a flange on both ends
  4. Wall thickness in mm

Detailed installation instructions enclosed with the product.


Curaline KD 110 Assembling in batteries

KD 110-1×3-K2/(L) Ordering example: Single flange sleeve

KD 110 -K / (L)

Angled sleeve

Installation sketch for sleeve at 45° angle

Subject to technical alteration without notice


KD 110 Sleeves with flanges/system cap

Single flange sleeve suitable for installation of system caps or KSS system on one end, for min. wall thickness 60 mm. Correct direction of installation must be followed.

Order No.: KD 110-K/L

(L) = Wall thickness in mm

Double flange sleeve suitable for installation of system caps or KSS system on both ends, for min. wall thickness 140 mm.

Order No.: KD 110-K2/L

(L) = Wall thickness in mm

Angled sleeve for angled cable entry from any direction at 30°, 45° or 60° with installation form and polystyrene wedge, sleeve with a flange on one or both ends, also available as a multiple battery for min. wall thickness 250 mm.

Angled single sleeve

Order no.: KD 110-S30-K2/(L)
KD 110-S45-K2/(L)
KD 110-S60-K2/(L)

(L) = Wall thickness in mm

Conical gasket insert made from highly durable EPDM elastomer for sealing cables (Z) up to 110 mm dia. (D).

Order No.: KD 110-WA/ZxD

Conical gasket insert made from highly durable EPDM elastomer for connecting 110 mm outside dia. cable duct.

Order No.: KD 110-WA/1×110

System cap with plug in bushing to connect smooth-faced cable duct with 110 mm external diameter. An O-ring on the inside of the bushing provides the seal.

Order No.: KD 110-DSM 110

System cap with one spigot and accompanying heat-shrink sleeve, suitable for one cable.

Order No.: KD 110-D1/100 for cable: 34 – 98 mm

Order No.: KD 110-D1/80 for cable: 26 – 78 mm

System cap with three spigots and accompanying heat-shrink sleeves, suitable for 3 cables with diameter 16 – 44 mm.

Order No.: KD 110-D3/46

System cap with seven spigots 6 are open with accompanying heat-shrink sleeves and one is blanked off, suitable for 4 cables 7 – 23 mm diameter and 3 cables 12 – 30 mm diameter.

Order No.: KD 110-D7/32/25

System cap with cuff

Order No.: KD 110-DMM 75
KD 110-DMM 80
KD 110-DMM 110
KD 110-DMM 125


Additional protection plug: KD 110-D

KD 110 Accessories

3-finger shrouds (heat-shrink type) for sealing 3 cables in 1 spigot.

Order No.: AK 35-3F-12/2 for system cap KD 110D7/32/25 and cables 2 – 12 mm diameter

Order No.: AK 50-3F-22/5 for system cap KD 110-D3/46 and cables 5 – 22 mm diameter

4-finger shrouds (heat-shrink type) for sealing 4 cables in 1 spigot.

Order No.: AK 35-4F-13/2 for system cap KD 110-D7/32/25 and cables 2 – 13 mm diameter

Order No.: AK 50-4F-20/5 for system cap KD 110-D3/46 and cables 5 – 20 mm diameter

Blind plug VS seals unused spigots, removeable for retrofit installation of cables. Available for spigots 25, 32 and 46 mm diameter.

Order No.: VS 25 / VS 32 /VS 46

Melt-tape – SKB a self-fusing tape with excellent adhesive properties, tape thickness 1 mm, tape width 50 mm, roll length 3.00 m

Order ref.:SKB

Articulated spanner – GSS with adjustable arm for removal and assembly of sleeve protection plugs, system caps and KSS duct adaptors.

Order ref.:GSS

Square socket key – VMS for rapid removal and replacement of KD 110 sleeve protection plugs.

Order ref.:VMS

Set of heat-shrink sleeves Order No.: KD 110-TM Set-D8

Cold shrink sleeves on request.